Anker’s Ultra Slim Extended Battery Case provides the best combination of good performance, price for that capacity, and physical size (the level of bulk it boosts the phone). They have the capacity to provide 117 percent of any full charge with an iPhone 6 or 108 percent to an iPhone 6s. The price tag, $40 at this particular writing, is crazy low for the battery case: At this rate, the Ultra Slim offers the best charge value (a 2.9 percent charge per dollar, or $34.34 for the full charge, to the iPhone 6) of some of the cases we tested, certainly.
The Ultra Slim doesn’t come with an especially premium feel. That’s not to say it comes off as cheap, but nothing about its physical construction is very impressive close to other cases. Another minor strike against this Anker case is its absence of button coverage; we usually prefer (well-designed) press-through button covers that protect the iPhone’s various buttons minimizing the quantity of places where dust and dirt could possibly get underneath the iphone6 case supplier.
For the iPhone 6 Plus and 6s Plus
Anker doesn’t make an Ultra Slim to the iPhone 6 Plus or 6s Plus, so for people handsets, we like the Tylt Energi Sliding Power Case. Unlike a lot of the models we tested, this one includes a separate protective case you could slide out from the battery sled whenever you don’t require the extra power, so that it is a much more-practical choice for the already huge Plus models. It’s another great source of energy, providing generally a 93 percent charge towards the iPhone 6s Also in our tests.
An important thing to remember with the cases we dismiss below is that they usually are not necessarily bad. Although we’re noting any issues we saw with one of these cases, a number of them are fine-they merely can’t quite match towards the good quality of our own picks.
Our previous pick for any more protective case was Speck’s CandyShell. A perennial favorite, they have two layers of material-plastic on the outside, rubber on the inside-that supply more protection than case designs that happen to be just one or maybe the other. The CandyShell is 10.9 mm thick, which puts it in the chunky side, however it doesn’t feel exceptionally bulky, and it’s one of the only cases we tested that claim to meet military drop-test standards. Speck supplies the case in a variety of colors, and variants add rubbery grips (CandyShell Grip), credit card holders (CandyShell Card), and graphic prints (CandyShell Inked).
The CandyShell carries a few issues that ensure that it stays from becoming a top pick, though. For starters, the CandyShell’s glossy back very quickly attracts small scratches that generally aren’t visible go on but jump out whenever you look at the iPhone with an angle. Granted, these scratches don’t affect the protection the case offers-and we’re needless to say happier to view scratches around the case rather than on the phone itself-but it will be nice if Speck were to offer the case with a matte finish.
Other problem is the case’s shape. A lot of our readers, and also a contingent of Amazon reviewers, take trouble with the truth that the CandyShell’s back is slightly convex. Specifically, if you set the truth on the flat surface, this “hump” causes the truth to rock whenever you press along any kind of its edges, or perhaps to spin such as a top if you push it. (In the event you bought a CandyShell and also you mind this spinning and rocking, Speck says to contact its support service department.)
OnePlus (the Android phone maker) surprisingly decided to go into in the iPhone-case game with its Sandstone Case. The large draw is OnePlus’s Sandstone texture; TIME says that it “feels like smooth sandpaper” which “[i]t’s super grippy, so that it is very difficult to drop.” Unfortunately the case is a shell with open top and bottom edges, meaning it’s less protective compared to a good case should be. Because of this design drawback, it fell from competition.
SwitchEasy carries a mixed history, one which makes it tough to tell the complete story according to its cases alone. Its Numbers case was our original pick for your iPhone 5 and 5s, before a wave of reader complaints about quality and customer service. The answers we got from SwitchEasy weren’t thorough; mostly, the corporation blamed the difficulties on third-parties selling knockoffs of its products. (At iLounge, I stumbled upon the SwitchEasy protectors to become impressive in general-the Numbers earned a rare A rating from me-but readers there contacted me about similar issues.) Ultimately, we pulled our recommendation.
With all of that in your mind, we considered three SwitchEasy cases for the iPhone 6. The first is the Odyssey. Like a few of the better cases we’ve evaluated, it’s a combination of plastic and rubber. Rather than being layered, materials run alongside, using the hardened rubber making up the majority of the case. It isn’t the prettiest case, in your opinion, however it is protective. It covers the buttons without reducing most of their clickiness, and six holes along tha harsh truth up precisely with the speaker vents. The most popular section of the case is definitely the port protection: Rubber protectors match the headphone and Lightning ports, respectively, when they’re not being used, keeping dust and also other debris out.
SwitchEasy’s Tones includes the same port protection and uses the identical materials. The entire body is generally plastic, though, with all the rubber walking around the sides like a border along with across the back of the truth, matching the iPhone’s antenna lines. We’d should you prefer a layer of rubber between the handset and the plastic back of the TPU iphone6 case supplier, and also the Sleep/Wake button demands a bit a lot of pressure on the couple of units we tested.
Our initial impressions of SwitchEasy’s Numbers were very positive-we had been willing to name it as our top pick-but there’s far more for the story than just our review units, so we found a significant fault after a little extended use. This example is almost just like the Incipio NGP, nevertheless it provides more protection. As opposed to leaving the phone’s ports totally exposed, the case provides protectors which fit in to the headphone-jack and Lightning-port openings to keep dust and debris out. It’s a good touch that’s executed well. Including the phone’s speaker is preferable protected, with six individual holes instead of one long opening. We actually much like the tactility of your devqpky94 a bit more with SwitchEasy’s model as compared to Incipio’s case, too. An earlier yellow version of your case we tested accumulated permanent stains, but later iterations exhibited no such issue. However , the case is a bit too loose, therefore the corners appear too easily. We experienced this concern time and time again while eliminating the encased phone from our pockets. Because we’ve had other conditions with SwitchEasy cases before, we’re still a bit wary. Should you choose to invest in a SwitchEasy case, we recommend buying it directly with the company’s website. Doing so will eliminate any potential warranty complications with third-party sellers, if you have any issues with the way it is.
An essential thing to remember together with the cases we dismiss below is the fact that, unlike with other types of products we cover, they are certainly not necessarily bad. Although we’re noting any issues we saw by using these cases, some of them are fine-they simply can’t quite match up towards the good quality of the picks.
Combining a rubber skin by using a plastic frame, the Spigen Neo Hybrid is really a slim, attractive case. Its fatal flaw is in its button protection. The silver plastic pill on the Sleep/Wake button doesn’t depress properly, so it might not hit the control underneath, and you also likely won’t feel it if it does. Former Sweethome editor Joel Johnson confirmed this problem together with the iPhone 6 Plus version. Because we received this situation for testing so early, we think Spigen might revise later editions to address this challenge.
Also from Spigen is the Ultra Hybrid, a single-piece case that fuses a rubber frame with a clear plastic back. It’s a nice-looking case, but when again, it has complications with the buttons. As an alternative to putting raised material over them, it has left and right edges which are flat all the way through with small indentations. For that Sleep/Wake button, the indented label says “PWR,” and then for volume, you receive plus and minus signs. With out a more pronounced physical distinction, you are able to more easily miss the buttons, and also the frame moves inward if you press.
Twelve South is up front about just how protective the SurfacePad is. Within the FAQ portion of the case’s website, the business says, “SurfacePad for iPhone is not designed to protect iPhone from falls, drops, being run over from a car or dropped within the loo. SurfacePad is meant to guard your iPhone from scratches and scrapes from things such as car keys, nail files or concrete park benches.” It’s actually a lesser case and a lot more of the leather sticker using a cover. The SurfacePad adheres to the back of the iPhone, and you could get rid of it and reapply it necessary (though the process is just not as simple as the organization might have you believe). We like the types of materials, however the SurfacePad is difficult to recommend unless your primary concern is fashion.
The Vault Slim Wallet from Silk is a much-less-expensive substitute for sister company CM4’s Q Card Case. It’s basically the same design, except as opposed to a faux-leather back, everything is made from TPU. Just like the Q Card Case, the Slim Wallet can take three cards, but a raised arch in its card slot causes the cards to curve to your noticeable degree, which can damage the cards as time passes. The Q Card Case’s positive attributes otherwise carry over, but because of the card bending, I’m a little cautious about the Slim Wallet.
Silk even offers the Armor Tough Case and PureView Clear Case. The Armor Tough Case can be a rubber case with interchangeable, polycarbonate-plastic backplates. It’s an excellent case at a reasonable cost, but it’s thicker than than our top pick, the NGP. The PureView Clear Case, on the flip side, is a nice pick within the very full class of cases with rubber edges and clear backs, and Silk prices it aggressively. But we’re not terribly fond of this style due to dust’s propensity to acquire under the transparent back, and due to the benefit in which the plastic can scratch. Still, beside others we’ve tested, the PureView Clear Case has pleasant-feeling buttons and well-sized port openings.
With Incipio’s Rival, unlike with the NGP, only the border is TPU; the remainder of the Rival is challenging plastic, about .3 mm thicker in comparison to the NGP. Everything else about the case is largely the same as about the NGP, like the cutouts for that ports and the quality of the button protection. While the Rival is extremely smooth, just like the NGP, horizontal lines across the lower two-thirds of its back give a distinct texture. It isn’t as neutral as the NGP, but if you like the design and style, this is a good option.
Tech21’s Evo Mesh, which features another generation of the company’s shock-absorbing lining, is surely an Apple Store exclusive. Just like Tech21’s Classic Shell (more on this design below), it’s a rubber case with a colored band running around the perimeter. The dimensions are basically identical involving the two. There’s something relating to this one that we like more than the Classic Shell, but it’s tough to put a finger on what that is. Perhaps it’s that this somewhat-obnoxious orange band has been replaced by colors matching the numerous body shades from the case itself. Overall, though, this case is way too pricey for the purpose it will give you.
Plastic and rubber with a clear back, the ITSKINS Venum Reloaded drops the ball in terms of covering the iPhone’s buttons. Similar to the setup of Spigen’s Ultra Hybrid, the design of your Venum Reloaded makes virtually no physical distinction involving the button coverage and the other case. This example have also been relatively expensive when last we checked, and also the plastic border frame feels fragile.
Really more of a fashion case, the Nitro Forged from ITSKINS currently costs quite a penny at nearly $70. It includes rubber skin with machined aluminum caps that attach at the very top and bottom. Thankfully, this design is an improvement over previous versions, which required you to utilize an included screwdriver to install and remove the caps; instead, it uses small plastic clips that one could devote and take away by hand.
Also from ITSKINS is definitely the Evolution. A rubber core with a plastic frame, the Evolution has some curves that assist allow it to be feel slightly more organic. The large problem is the fact that screen rises above the edge of the way it is instead of the opposite. Because of this should you drop your handset, there’s a lot more possibility of harm to the display compared to other cases.
Incipio makes a lot of cases that we can’t expect great things out of every one. The Advantage is a plastic slider, a style that’s relatively rare currently. The smooth, matte-finish plastic splits into two pieces for both installation and docking purposes. Even though it offers proper button coverage along with a nice protective lip, we found the situation being too tight; pulling it away, specially the bottom cap, can be a struggle.
Weighing a few grams greater than the average of all of the cases we tested, the DualPro SHINE is a solid contender from Incipio. It incorporates both plastic and rubber layers, although rather than being molded together, they’re two distinct pieces. The rubber is quite thick but doesn’t dampen the tactility of the buttons in any way, and it still provides acceptable accessibility ports. The port openings are exactly the same as the NGP’s. We checked out the conventional DualPro, that features a matte finish. It’s quite nice, but it’s thicker in comparison to the NGP and lacking the mil-spec rating in the CandyShell.
The plastic layer from the DualPro SHINE suits grooves from the rubber, improving the case feel as if a cohesive unit. We believe the most polarizing point about this case is its texture: Made to appear like brushed aluminum, it certainly doesn’t feel as if that, and also at least in your tests, the end result can be a certain measure of cognitive dissonance. It’s not necessarily a bad thing by any means, but overall it just doesn’t feel quite as nice as it looks.
If card storage is very important to you personally, Verus’s Damda is a fine case. The entire body is made from black rubber, with nice button protection and properly centered openings for your headphone port and microphone, the Lightning port, along with the speaker. Attached to the back is a plastic compartment that adds both mass and depth. A plastic door slides open to reveal space for a couple of, maybe three, a credit card. We initially thought it was a bit challenging to open, although with some cards in there it’s easier to work with but still secure. This can be much more of a distinct segment case than our pick.
Verus’s Crystal Mixx offers a transparent window along with a rubber frame. The back for this one is plastic, that is one of the two drawbacks. Within our knowledge of iPhone cases, clear plastic scuffs easily and will show those scratches within an issue of days. This example might not be so bad when the frame provided a better lip. Unfortunately, at .3 mm, it’s one in the shortest lips we saw, and it can lead to problems should you drop your iPhone.
The Protector Case and Voyager Case from Pelican look a great deal alike, and each model is difficult to get-Pelican doesn’t sell them online, and in our experience they’ve been reliably available limited to AT&T retail shops. The Protector can be a bulkier, more-angular carry out the CandyShell design with no additional benefits, so we’d pass into it. The Voyager adds port protection and funnels the sound from your speakers forward. Furthermore, it has a belt clip and screen film. We percieve this model as an alternative to an OtterBox case, as it’s basically overkill. Many people simply don’t need this degree of protection, especially not should they have to get out of their option to finding it.
PureGear’s Slim Shell Case is available in seven color combinations, including clear-on-clear. This model is challenging plastic using a rubberized but nevertheless rigid frame. The metal button covers can be a very nice addition, improving the case feel more premium. It won’t offer just as much protection as a CandyShell, so it isn’t a top pick, but this one isn’t an unsatisfactory option whatsoever.
One of the 1st iPhone 6 cases to get publicly sold-we saw it since May 2014-Minisuit’s Frost is undoubtedly an inexpensive TPU skin. Even though it does fit, they have very little lip, and the holes along the bottom are uneven to the point of looking warped.
Monoprice is known for inexpensive products of all sorts. We love a few of the company’s accessories-it makes great cables, by way of example-but Monoprice cases generally don’t impress. The materials often feel cheap, and also other companies offer higher-quality products at similarly low prices. For example, the Metal Alloy Protective Case (offered in gold, silver, and cosmic blue) includes thin, aluminum shell that snaps over a thin TPU skin, with lines matching the iPhone’s antenna breaks. The TPU doesn’t feel as nice since the material that Incipio and also other companies use, as well as the case exposes the Apple logo on the rear of the phone.
Monoprice’s Industrial Metal Mesh Guard Case (in black or white) feels a lttle bit nicer but is much less protective. The plastic shell has features a cool-looking steel grille over it, however it leaves the top and bottom edges unprotected, and yes it features the biggest Apple-logo opening we’ve seen on any case.
We checked out the TPU case from Insignia, a Best Buy brand, and it also seems to be from your same OEM as Monoprice’s TPU case, but at the higher price.
We don’t such as the Monoprice PC TPU Protector Case as much, though it does offer arguably more protection. This model splits into two pieces, with an inner skin of TPU along with a polycarbonate shell that snaps into place over it. The case is fairly simple to assemble, but once it’s together, it simply feels big. It’s both wider and thicker compared to NGP, without the obvious advantage other than price.
Rokform has long dedicated to ruggedized cases that can connect to an ecosystem of mounting accessories. Its Sport v3 is no exception. This plastic and rubber case incorporates swappable magnetic backplates that give it time to get connected to various mounting brackets the company sells. Unfortunately, the instruction insert lists a dealbreaker: “Magnet will disable NFC on phone.” Nowadays the corporation claims that the magnet won’t affect Apple Pay or any antennas, but we haven’t tested this.
OtterBox’s Defender Series may be the bulkiest in the cases we’ve tested thus far. This is actually the company’s flagship case, the one many people associate with the brand. It’s made up of a plastic frame that snaps round the handset and a thick rubber skin that covers the whole thing. Unlike many other cases, this model includes flaps on the vibration control switch, headphone port, and Lightning port-all great things for an extra degree of protection. It also includes button coverage, but we learned that it requires more force to depress the volume and power controls than other cases do.
The Defender Series can also be the only real case we’ve tested with built-in screen protection by means of a clear film integrated into the frame. Because you end up with a little space between your protector as well as the screen, very light presses and swipes may not register, and that is a drawback. Atop the Touch ID/Home button is a thin sheet of plastic that didn’t hinder the experience in our testing. As the Defender Series does expose the Apple logo, the case a minimum of covers it with clear film that prevents it from getting scratched. And also as an added bonus, the Defender Series has a belt holster.
Inside the OtterBox family, the Commuter Series represents the next thing down in overall protection. As opposed to plastic inside and rubber on the outside, the layers are reversed. The truth still offers port coverage, however the switch on the iPhone’s left side remains exposed. Thankfully, the buttons depress considerably more easily. Instead of a permanent screen protector, OtterBox includes an optional film using this case. The Apple logo is once more exposed, this time without plastic covering it. Besides the port protection, this case offers no obvious benefits across a CandyShell, as well as the dimension is a drawback that keeps this model from earning a top spot.
The Symmetry Series is actually a relatively recent accessory for the OtterBox lineup and the slimmest of which all. It feels as though a direct response to the CandyShell, with its dual-layer design. This case supplies the same degree of protection as our top choice and a substantial lip. It’s taller and wider, though, at a higher price. The biggest benefit is the fact by using a matte-plastic back, it won’t show the scratches that the CandyShell does.
OtterBox’s newest case, the Statement Series, is definitely an iPhone 6/6s-specific case. An iPhone 6/6s Plus version exists, but unlike OtterBox’s other lines, this series offers no version for older iPhones or any other flagship smartphones. It’s also one from the few OtterBox cases that put aesthetics first, using its large back-panel window and leather-covered lower quarter being its key distinguishing features. We’re testing the Statement right now, and we’ll decide if it should join our picks soon.
The Tough Candy Cases Candy Clip Series is a pretty crazy proposition: For $30, you have a hard-plastic X-shaped piece that snaps onto the back of the iPhone, covering its corners and a few of the edges but leaving the buttons and the majority of the sides exposed. No thanks.
Urban Armor Gear’s Case is one in the only cases we’ve tested to satisfy military drop-test standards. It’s excellent as being a protective case, but its industrial aesthetic lacks the broad appeal of simpler designs like those from Incipio and Speck. UAG also combines plastic and rubber in this case, but rather than a glossy finish, it uses a matte one, with an industrial appearance that appropriately matches the brand’s name. With ridges and fake screws, it appears like something that would not out of place over a construction site. We all do take issue with both small, rectangular holes on the back of the case-with regards to a quarter of the way through the top or bottom, respectively, they expose area of the logo and also the top one half of “Phone” within the iPhone label. It’s a strange design decision by using an otherwise impressive case. On the flip side, this model does have a screen film, whereas most iPhone cases don’t these days.
Tech21’s entire product lineup is founded on D3O, a licensed material the organization uses in every one of their cases. Mostly contained in the borders of Tech21 cases, the brilliant-orange material should really remain soft when at rest but automatically harden upon impact, dissipating the force and ultimately preventing injury to your phone. The business really likes to demonstrate the stuff; all of its cases are at least translucent, otherwise transparent, round the edges.
From Tech21, we tested the Classic Shell, Classic Shell Cover, and Classic Shell Flip. The initial one is the standard, a glossy TPU skin that’s wider compared to the NGP, thanks to the layer of D3O. We’d love to notice a bigger lip than this situation offers, as well as the buttons really are a bit squishier than we generally prefer. The Classic Shell Cover keeps exactly the same frame but replaces the TPU in the back using a hard-plastic plate, and has an attached cover to guard the iPhone’s display. Anything else works exactly like with the standard model, as well as the lid carries a cutout over the earpiece in order to speak in the phone from it closed. The Classic Shell Flip is basically exactly the same, only rather than plastic this case features a leather feel (it appears to be the fake stuff), as well as the lid comes around through the bottom rather than the side. We find that lids get in the way more than they help, so neither of the covered models excites us, along with the soft buttons and wider body in the Classic Shell prevent it from obtaining a recommendation.
From iLuv, we received two cases for evaluation: the Aurora Wave and Gelato. The first is a simple silicone skin with a grid on the back that glows at nighttime. When it comes to body coverage, the truth lives around what we’re seeking, but making this type of design involves a low standard of difficulty. As we’ve often found with cases of this style in the past, the vertical edges can pull away from the body from the phone more readily compared to other cases, allowing dust as well as other particulates to have underneath. The Gelato, alternatively, is iphone7 case with the attractive checkerboard pattern around the back. It seems and feels pretty good, however the .33-millimeter lip is way too short.
Poetic’s Atmosphere is a thin case made from dual-molded polycarbonate plastic and TPU. The softer material rings the leading edge to make a small lip, and it likewise runs across the antenna breaks on the rear of the phone. While this transparent case initially seems like a fantastic option for those who desire a slim protector yet still want to exhibit their iPhone, it falls short due to button protectors which require too much force to press.
Macally shipped us a handful of different cases, but two are styles we simply can’t recommend. Both Metallic Snap-On Case as well as the Flexible Protective Frame come in a variety of colors, nevertheless the former is a shell, along with the latter is really a bumper that protects the edges but leaves the scratchable back exposed. The Durable Protective Case, on the other hand, does offer more thorough protection, however it isn’t a unique design. A combination TPU skin and hard-plastic frame, this situation type of looks like an armadillo from your back. We’ve already seen at least one other company offering the same case, and we weren’t impressed with that case’s aggressive looks either.
New Trent’s Alixo 6S isn’t necessarily the prettiest case around, but it is one of the more original designs we’ve noticed in the pile. This two-piece case includes front frame (black- and white-rimmed versions are within the package) plus a silicone rubber and plastic back. You only snap the phone into your selection of frame and then insert it into the back piece, which includes flip-open port protectors. The quantity of protection this model offers for that cost is impressive, as it contains a built-in screen film and Touch ID coverage. Nevertheless the latter turns out to be the Alixo 6S’s downside: While the fingerprint sensor does deal with the thin material over it, we found it to be less reliable, requiring more attempts to unlock the product.
Marblue’s ToughTek is really a thick silicone rubber case that accompany a screen protector. Basically we don’t doubt this thing can tolerate some significant drops, the ToughTek is huge-3 inches wide, 5.8 inches tall, and .6 inch deep-and particularly difficult to go into and out from tight pockets due to the grippy material. It may not be described as a bad option if you’re handing your iPhone 6 to kids.
The Elite, also from Marblue, takes its inspiration in the CandyShell, while incorporating an Aztec-like pattern. The plastic and rubber layers intersect in horizontal and vertical lines, with the latter material sticking up on top of the hard plastic. By far the most intriguing part of this case may be the kind of inch-long ridges, one on both sides. They’re made to do business with an array of accessories, such as a belt clip. We’ll be keeping an eye out for such accessories, and we’ll see whether they boost the need for the truth.
We had high hopes for the Spigen Capella, which comes in multiple colors. Its setup is much like the CandyShell’s, with rubber inside and plastic outside. The large difference, and the reason we were excited about it, is it’s much slimmer, measuring about 2 mm thinner from front to back. This is certainly partly because of the smaller, half-millimeter lip across the screen. One of our editors loves just how the case’s slight curve feels, comparing it for the iPhone 3G. Judging from the feedback we’ve seen from readers and Amazon reviewers, many people don’t like this shape as much as we do.
Even though the Capella isn’t as deep since the CandyShell, this is a bit taller, and about 3 mm wider. This width ends up being problematic for two reasons, one on either edge. About the iPhone’s left side, the switch is much harder to toggle, as it’s deeply recessed inside the rubber border; if you don’t have nails to talk of, moving it backwards and forwards will likely be tough. On the opposite side, the Sleep/Wake button takes a surprising quantity of pressure to activate. If you’re willing to deal with those drawbacks, the Capella is otherwise worth considering being a CandyShell alternative.
With its Revolution case, Poetic is looking to take on companies for example OtterBox at a reduced price. The situation begins with a plastic frame that snaps into the front of your iPhone; a precise sheet of plastic protects the screen while leaving the sensors at the top and the Touch ID button at the bottom exposed. A rubber and plastic body fits across the back, snapping into position with the front piece. Everything feels quite sturdy, the buttons click well, and the flap over the Lightning port is actually a nice little bit of extra protection.
Supcase’s Unicorn Beetle Pro Holster delivers a similar proposition. The biggest difference between this model as well as the Revolution is that it includes a plastic belt holster. Having roughly exactly the same dimensions as the Poetic case, this model requires an installation that’s just about the identical. This case adds a number of flaps for coverage, namely on the side switch and the headphone port along with the Lightning port. While it’s an incredibly solid-feeling case, we immediately referred to as company’s claim of dust-proof construction into question, since it leaves openings for dust to go into, including the fully exposed speaker. Currently, Amazon users are generally fond of it, with 127 reviews and a 4.1-star (from five) rating, but we’ve seen a number of three- and four-star reviews.
Relative newcomer Supcase has a variety of iPhone 6 cases, in reality, almost all of that are part of the “Unicorn Beetle” family. The Slim Armored Protective Case is a lot like Urban Armor Gear’s case because it’s protective, but the design is quite specific, meaning it likely won’t interest the identical wide swath of folks as something much more generic. The plastic and rubber case feels sturdy and it has a few of the clickiest buttons associated with a we tested. As for the lip, it’s approximately .5 mm, so it’s smaller than we’d like, along with the case makes no mil-spec claims. If you appreciate the style, it’s not a bad choice otherwise.
Supcase also sells the Hybrid Clear Bumper Case, which combines a specific-plastic backplate by using a TPU bumper. That polycarbonate back won’t absorb as much shock since the thick rubber border, but it’s a good way to show off Apple’s design.
In the previous version of the guide, we named Logitech’s Protection [ ] as an even more-protective pick. It possesses a very similar design, with the benefits of a matte finish and embedded magnets that allow it to get connected to mounting accessories. Unfortunately Logitech has confirmed that it’s no longer selling the case, which happens to be currently on clearance at Best Buy.
Not one other case we tested is to establish exactly the same way as Maxboost’s DuraShield Series (now named DuraSLIM). Like various other models, it uses both rubber and plastic components, but here the rubber is really a bumper that wraps throughout the iPhone’s border, along with the plastic snaps in position over it while covering the back of the handset. Inspite of the unusual design-or maybe because of it-the situation offers superior protection compared with many more we’ve seen. It offers a 1-mm lip, plus speaker and Lightning-port protection. It also redirects the audio ports forward, meaning the sound comes at you, rather than down; the design has no effect on audio quality, thankfully. When it comes to Lightning port, it stays protected underneath a rubber tab that you could flip out if you want access.
Few case manufacturers actively warn their product doesn’t offer drop protection, however this sort of message appears on the Amazon listing for Maxboost’s Liquid Skin. Extremely thin, this transparent-TPU case adds hardly any bulk to the handset, not even a protective lip. It’s much better than a shell mainly because it offers button protection and cutouts for that ports, even should they be quite tight. However with such a warning in the case maker itself, we can’t recommend the Liquid Skin for many people. If you’re going to utilize a case, you may use something that’ll resist a drop.
Maxboost’s Crystal Cushion and so i-Blason’s Halo Series are almost identical to one another and also can be small tweaks on the very same reference design. Both have rubber frames-the Halo Series offers six colors, plus clear-with transparent plastic backplates. The Maxboost case’s edges are more squared-off, whilst the i-Blason’s are rounder. Both offer good body coverage and responsive buttons, however the lip round the screen is nearly nonexistent, especially in the Halo Series. Combine that with the tendency for clear plastic cases to scratch as well as to expose trapped dust underneath, and those cases aren’t top picks.
The Maxboost HyperPro Series is for all intents and purposes a thicker version of your Incipio NGP. Available only in black, it uses two layers of TPU to safeguard the iPhone, and it measures 10.2 mm thick; it’s also wider and taller than our pick. The buttons press well and yes it incorporates a protective lip, but we can easily find no real help to this situation over the NGP, besides savings of just a couple dollars.
One of only a few slider-style cases out there, Maxboost’s Vibrance Series provides a different build than the majority of the cases we tested. A difficult-plastic case, it splits into two pieces, both lined having a soft fabric over the back that’s created to prevent damage during installation and removal. As opposed to pushing the phone in the case, you accomplish the bottom cap, slide the phone into the top, and after that push the pieces back together again. Much much like the STM Harbour, this sort of design lets you keep your iPhone thoroughly protected usually, as well as plug it into docks when needed. The lip is sort of short, though, and pulling from the Vibrance’s bottom cap is harder than flipping in the Harbour’s bottom. Maxboost also provides only one color choice, salmon with a gold cap, which could not interest several people as more basic colors would.
If you find the CandyShell being too big, you won’t be impressed with Speck’s MightyShell, which can be found in black, orange, purple, pink, and clear variants. This model has a few key differences. First is definitely the extra layer of TPU material that assists absorb shocks to your greater degree; it adds 2 mm in both width and height, along with .5 mm to the thickness from the case. Speck claims that it new design will “double MIL-STD-810G drop test standards,” but we can’t tell whether it means the case is tested to live drops from two times as high or this means the way it is can tolerate the standard 4-foot drops twice as many times. One aspect of the case we actually appreciate will be the hard-plastic exterior, which happens to be matte as opposed to glossy, so that it won’t show scratches as readily because the standard CandyShell. To the price, we expect not just claims of better drop protection; instances by which this situation would survive but a CandyShell wouldn’t are too ambiguous to warrant the charge.
Among ultrathin cases, Shumuri’s SLIM looks and feels much like Caudabe’s The Veil XT, right down to the possible lack of the standard Veil’s screen-protection lip. But it’s also missing both Veil models’ camera-lens protector. The same goes for Monoprice’s Ultra-thin Shatter-proof Case (in clear frost, ice blue, and smoke) and Totallee’s The Scarf (for iPhone 6 and iPhone 6 Plus).
Rearth USA’s Ringke Slim (for iPhone 6 and iPhone 6 Plus) offers both a screen-protecting lip and bottom-edge coverage, as well as thicker plastic for added protection. However, we’re not fans of its aesthetics-because the case’s rigid plastic is thicker, the business has added a tiny slit to each and every corner to make putting the truth in your phone easier. The design is useful enough; we simply don’t like the way it looks.
Power Support’s Air Jacket and SwitchEasy’s Nude (for iPhone 6 and iPhone 6 Plus) are glossy-plastic cases which can be slightly thicker than Caudabe’s The Veil. The first kind provides good coverage down the phone’s bottom edge but has only the faintest of your screen-protection lip. The second has neither.
Amzer’s Crusta may well not appear to be an excellent value at $35 (iPhone 6) or $45 (iPhone 6 Plus) since this writing, but the package includes more than simply a simple case. The case itself utilizes a two-piece snap-together design using a rubber bumper along with a glass back that lets the iPhone’s rear show through. The glass likely won’t show scratches as easily as similar cases we’ve seen having a plastic back, nevertheless, you will still see any dust, hair, or some other particulates which get beneath the glass. Amzer includes a second component of glass to safeguard the phone’s screen. The case eventually ends up being bulkier than we prefer-the iPhone 6 version is 14.4 mm thick, like the phone-but it’s one from the better cases we’ve seen from Amzer, a company otherwise noted for inexpensive, nondescript accessories.
NewerTech is well known more for computer accessories than smartphone add-ons, although the company does offer a type of cases called NuGuard KX (for iPhone 6 and iPhone 6 Plus). Made more for drop protection than sleekness, the NuGuard KX contains a thick layer of gel material that absorbs and evenly distributes shocks. The truth is pretty bulky, yet an opening on the back of the truth to the phone’s Apple logo actually subtracts through the overall measure of protection. We prefer the NGP.
We certainly have varying levels of praise for three cases from Griffin Technology. The Survivor Slim (for iPhone 6 and iPhone 6 Plus) is our least favorite of these. This bulky rubber case feels similar to an accessory for the kid’s toy than a smartphone. It could be a good case if children frequently use your phone, but we suspect that a lot of adults will prefer something slimmer.
We like the Survivor Core (for iPhone 6 and iPhone 6 Plus) and Clear Identity (for iPhone 6 and iPhone 6 Plus) better. Both allow the handset’s to show through a clear back panel. The first kind has rubber edges, and its particular rubber corners protrude a little, helping cushion the iPhone against drops-but the end result is that it’s a little bigger than a regular case. The All Clear Identity, however, has a transparent back with translucent-rubber edges. The situation, like all cases sporting a clear back, is the fact both cases show any gunk that gets below the plastic. For a few people, that might be an acceptable compromise in a case designed to let you view your phone’s own surfaces, but we generally prefer something translucent or opaque. Neither the Survivor Core nor the All Clear identity is really a bad option, but neither particularly excites us.
Belkin’s Grip Case for iPhone 6 is a good option to our top pick, but it doesn’t quite create the top tier. The design is much like those of the Incipio NGP, as it’s a one-piece polyurethane case. The most significant difference is throughout the phone’s bottom edge: Instead of having separate openings for that headphone jack, microphone, Lightning-connector port, and speaker, the way it is exposes the past two through one long opening. A little indentation inside the plastic covering the foot of the phone enables use with accessories like Apple’s Lightning-connector adapters. This can be a nice feature we haven’t seen on other cases, although we worry how the thinness of the material here, in addition to nearby the Ring/Silent switch, might make it more susceptible to ripping. Wirecutter editor Michael Zhao also finds the case’s button coverage being somewhat problematic, while he doesn’t like this they’re nearly flush together with the case.
Amongst the cases shipped to us for consideration, we also dismissed a number of models right from the start. We cut Spigen’s Slim Armor, Slim Armor S, Tough Armor, and Tough Armor S, together with Verus’s Thor, Iron Shield, and Dandy Diary, plus PureGear’s DualTek, because of the Apple-logo-exposing holes around the back. They do a decent job of protecting your phone otherwise, but we are able to imagine absolutely no reason to recommend them for most people when existing hole-free options are pretty much as good or better.
We dismissed a number of shell cases because, when we mention above, they give a minimal quantity of coverage for your device’s body. Among they were the Aluminum Fit, Thin Fit, and Thin Fit A from Spigen. The same thing goes for that Neo Hybrid EX, Spigen’s bumper case, that offers much less protection.